Rubber Band Tension On Tattoo

Machine Assembly Check list, Tuning, Troubleshooting

Amature Tattoos

"When you've got crossed wires, everything's buzz buzz, everything's beep beep "

Once the machine is assembled:

Re-check the parallelism of the armature bar to yoke. Do this by pushing the armature bar onto the tops of the coils (p. 54), press down on the armature bar itself NOT by pushing the front spring as this will change the tension of that spring, if it is not parallel, make corrections- shims, filing etc.

Tattoo Machine Spring Placement

This machine was a "reward" from a manufacturer because the customer bought $500.00 dollars worth of products from them. The armature bar is not parallel, first because it's not pulled down onto the front coil. It cannot be pulled down because the back of the amature bar hits the rear corner of the coil post which prevents any further examination until this issue is dealt with. It will take some work to make the armature bar parallel with the yoke/base of the frame. Take a look at the photos below.

Tattoomagik Info
These are the products manufacturers sell us. Educate yourselves, learn to fix these problems, don't let them make our industry "cheap".

Re-check for a small space between the rear coil and the armature bar, shim the front coil if necessary, while maintaining the parallelism.

Re-check for a small space between the rear coil and the armature bar, shim the front coil if necessary, while maintaining the parallelism.

Armature Bars Line Tattoo
Shim the front coil if necessary to make the armature bar parallel with the yoke or base of the frame.

Shim rear coil with a washer between the frame to reduce the space between the armature bar and rear coil. It should be paper thin. Using a feeler gauge can raise the coil and lessen the space by precise and perfect increments.

Shim the rear spring with a squared off feeler gauge if needed. The machine on page 65 would need the rear spring shimmed to take the armature bar off of the rear coil and bring it a step closer to making the armature bar parallel.

Make sure no terminals or wires touch the frame.

Tighten all securing screws.

Set the stroke to be a liner or shader: (bend spring(s) for more tension, un-bend spring(s) to lessen tension, adjust the contact screw accordingly by loosening or tightening or re-locating place of contact.

Perform the " Spring Tension Test" (p. 60) and run the machine.

Re-adjust the stroke if necessary and perform the "Ball system" (p. 61)

By now, you should have a pretty good idea on what needs to be done. The machine's components should be secured snuggly, the contact screw should be in it's place and the only adjustment left to do should be minimal.

Look at the machine head on from the front:

Make sure it all lines up— an imaginary straight vertical line should run down from the contact screw, through the front spring, through the nub on the armature bar, and the needle bar should run through the center of the tube and the needles into the tip of the tube.

Tattoo Machines Rubber Band

Once you have checked the assembled machine and have it running, and have set it up with a tube and needle bar, it's time for further fine tuning.

Turn the machine to look at it from the rear.

Check that the spring / armature bar assembly (rear spring, armature bar and front spring) is straight. Follow an imaginary straight line from the rear spring securing screw all the way through the tip of the front spring. This will ensure an even "bounce" when the machine is operating.

Tattoo Machine Exploded ViewCoil Tattoo Machine Assembly

Turn the machine to look at it from the side.

Make sure that the needle bar runs through the center of the tube or even a little behind center but should NEVER rub on the back of the tube, (only the needles should run on the back of the tip.) The needle bar should be as close to the coil as possible, the back armature bar nub should be back far enough to accommodate this (by sliding the rear spring back on the securing screw, if it stops on the"U-shaped" notch, the notch should be grinded out deeper with a dremmel. A frame's tube vice hole should be placed and-drilled into the frame to accommodate this as well.

Tattoomagik Info

Both photos are of the same machine. Note the needle bar's placement, traveling perfectly vertically from the armature bar's nub through the back center of the tube. DETAIL: Only one rubber band is needed to secure the needle bar enough to prevent any shaking of the needles.

Once the machine has had it's "lines" checked:

Performthe "Spring Tension Test"- the added weight of the needle bar, grommet / paper towel and rubber band tenesion should affect the travel of the armature bar very slightly once the front spring has stopped on the contact screw. The machine should not be running when performing this test.

Perform the "Ball System", the bouncing balls should move the same way as they did the first time this system was performed. The balls should not get closer to each other when turning down the current flow on the power supply. If they do, remove tension on the rear spring little by little. The contact screw should now be in it's permanent place.

Troubleshooting-Common problems

If you push the foot pedal down and the machine doesn't run:

Make sure there is contact between the contact screw and the front spring, with sufficient tension on the rear spring to push the front spring into the contact screw.

Check for metal touching metal- terminals touching the frame, wires touching the frame, grounding is the most common reason a machine won't run, or just look for wires broken inside the insulation, at the ring terminals or at coil base.

Wire terminals NOT making direct contact with the binding posts; may be accidentally assembled with a nylon washer between terminal and binding post.

Clip cord clips touching the frame.

There may be a break in the coil wire (rarely does this happen) at any point inside the insulation.

There is a good chance that the problem may be in the footswitch wires or footswitch assembly itself, or in the clip cord-wires themselves, check the jacks and terminals for bad solder joints...build a new clip cord or re-assemble the footswitch.

Check the fuse in the power supply and replace it.

Check the fuse in the power supply and replace it.

Fixing Wiring Inside Tattoo Power Supply

In the case of this power supply, the fuse housing is in the rear. It's popped off with a flat head screwdriver exposing the fuse. In this power supply, the fuse sits horizontally. A fuse is defined as: "A protective device consisting of a short piece of wire which melts and breaks when the current through it exceeds the rated value of the fuse..."

In simple terms, in the case that there is a power overload, a fuse will "absorb" this overload and become damaged in order to prevent any damage to the other circuits in the power supply. To check the fuse, remove it and look for a break in the thin wire which can be seen through the glass part of the fuse. If the wire is broken, replace the fuse. Always replace the damaged fuse with a new fuse with the same rated value (usually engraved on the side of the fuse's metal caps).

If you push the foot pedal down and the machine runs intermittently:

Check that the power supply is plugged into the wall completely

Check the soldering of the wire connecting to the terminals on the binding posts, or if no solder is used, check to see if the wires are NOT loose.

Check the wiring in the clip cord and footswitch jacks, there may be corrosion or loose solder connection.

Check the footswitch and clip cord wires for shorts by wiggling them every inch, from end to end, while keeping the pedal "on" with the machine attached, this will help locate the break in the wire. Replace the wire if necessary.

If the stroke drops when it shouldn't, check the following:

Rubber band tension- a tight rubber band(s) will create more resistance and cause the machine to work harder.

Check rear spring tension- too much tension will cause a fluctuation in stroke when turning down current flow. Lessen tension (un-bend the rear spring) if this is the case, until the ideal tension is found.

There may also be a break or small crack in the rear spring.

"...wire which melts and brea when the current exceeds t rated value of the fuse..."

Value rating is four the fuse's metal caj

Glass fuse housing.

"...wire which melts and brea when the current exceeds t rated value of the fuse..."

Value rating is four the fuse's metal caj

Glass fuse housing.

Tattoo Machine Fuse

Check for carbon build up, including on the clip cord ends that clip into the machine and file as needed to remove it.

Make sure there are no spring bends under any washers (spring saddle, armature bar assembly securing screw).

If the machine's power drops or raises and there is a big blue spark coming from the contact screw/ front spring:

Replace the capacitor.

How Tune Tattoo Machine Amataur Bar

General Maintenance

Over time, the constant use of the machine can deteriorate the it's function, just like in a car. Tune ups must be done to return the machine to it's optimal function. Checking it's non-moving parts and replacing the moving parts when worn, is necessary. Springs with excessive wear, or springs which simply need the tension re-set must be taken care of, loose rubber bands, capacitors breaking down must be replaced if necessary. To maintain your machine, here is a list of things to check periodically.

Periodically check the following:

Check rear spring tension and front spring flex.

Rubber band tension and quality. If it is dirty or starting to wear, or loosen replace it. Check o-ring tension, if loose and "saggy" replace it. Blue spark (replace capacitor if necessary). Look for exposed wires.

Check contact screw for carbon build-up; a file, steel wool or fine sand paper will remove this.

Check front coil for carbon build up, if you use tape as a "muffler", clean gummy build up on the armature bar and on the top of the front coil and remove with WD40 and replace tape on the armature bar.

Check the armature bar for wear from the constant friction against the front coil. If the worn groove is too big, simply flip the armature bar over and use the "new" clean side. Protect it with a piece of Trans pore tape over the area which contacts the front coil.

Check springs for cracks & check front spring for wear replace if necessary.

Check securing screws for tightness on the following: binding posts (upper and lower), spring saddle, rear spring and front spring joint screw (on armature bar), and the coils' securing screws.

Check the condition of the acrylic ball or thread protector for the contact screw (inside upper binding post) and check the threads on the contact screw.

Don't be afraid to take the machine apart, rebuild and/or replace parts!

Cutting corners or taking the easy way out gains you nothing!

Be a professional,

Join the professionals who know this information!

If you fail to prepare, then prepare to fail!

The Rubber Band

It seems silly to write a chapter on the "Rubber Band"...one of the very few non-mechanical parts included in the assembly and operation of a well running machine. It is such a simple ingredient in this process yet it needs to be addressed because this little band can make a difference in how a fully assembled machine (with a tube and needle bar) will run.

Some artists use 3 or 4 rubber bands on one machine, some use thick, tight rubber bands...most don't realize what they are doing...some of these artists think it makes them look "cool" or look like they know what they are doing. Truth is, that this simple item has a very important job to do and it's addition to the fully assembled machine should be taken very seriously.

The job of the rubber band is only to make sure the needle grouping, and needle bar don't shudder or wiggle when the machine is in use. Let's start at the begin-ning...earlier in this book, you read about springs and several times you heard about the weight and and resistance the REAR SPRING has to deal with. One of the most crucial burdens the rear spring has to combat is the tension of the rubber band. A rubber band that is too tight, will add to the resistance the rear spring spring has to fight against, in order to run the way it should. A rubber band that is too thick and tight will slow the movement of the armature bar. It may also keep the armature bar / front spring from returning (in it's upward movement) to make full contact with the contact screw this results in the machine not running. Again, the horizontal pull on the needle bar will make it's vertical movement more difficult by adding resistance to the rear spring. In addition, the bands will pull the needle bar, making it bow, this will move the needles away from the back of the tip of the tube. You can see this by simply pullling the rubber band tighter and watching the results. Watch the armature bar's movement slow down, watch the needle bar bow and the needles move toward the center of the tube tip's hole. Needles need to rub on the back of the inside of the tube, this is what helps the ink flow. If the needle grouping does NOT touch the back of the inside of the tip of the tube, no ink will flow, no pigment will be injected. Got it? So only one rubber band is enough. It is a good idea to stretch the rubber band before putting it on the machine...if ink is spitting out of the tip, check for shuddering or wiggling of the needle grouping, if so a tighter band could be used.

Prevention of cross contamination

Even though this book does not cover aspects of safe tattooing, there are a few practices which not only will help protect the artists and clients from health risks, but will also help protect the machine from corrosion.

Many artists spray their machines down with Madacide & many other types of disinfectants after tattooing, to clean the machine of any potential microorganisms. They SOAK the machine with these chemicals and let them dry on the machines. We discourage this practice because these chemicals can be corrosive to the steel screws, iron or steel coil posts, and springs. This rust and corrosion which develops, can "weld" the securing screws to the coils, weld the screws which secure the rear spring to the spring saddle onto steel or iron frames making the machine almost impossible to disassemble. These substances can get in between these steel or iron parts and will accelerate the oxidation, and leave a film on the rest of the machine. Prevention is better than cure, we recommend plastic baggies be put around the machine to minimize or prevent cross contamination, this is not to say that these bags will 100% eliminate any microbes from coming in contact with any part of the machine but it is harder to cross contaminate the machine frame when there is a barrier between the artists' dirty gloves and the machine. A paper towel or q-tip can be used to clean the machine off, slightly wet it and gently wipe down the machine and immediately dry it. Too much moisture in contact with steel or iron parts will start the oxidation.

It is NOT TRUE that machines heat up with a baggie placed around them, a well tuned machine will not heat up under any conditions, a rough running machine will heat up but again, this is NOT due to the use of a baggie.

Tension Wire Towel Bar
Jory "Angel of Death" Helmes is a responsible artist who uses a baggie on his machines.
Tattoo Shading Techniques

Tattoo Shading Techniques

Black with grey shading tattoo arts are like a representation of who you are and they have a power and magic of their own. This Tattoo tutorial is covering how to do black and gray portrait tattoo techniques. Learn about black with grey shading tattoo art and explore the exceptional techniques of making some beautiful designs.

Get My Free Ebook


Responses

  • Raimo Karlsson
    How thick should the armature bar be?
    7 years ago
  • Mandy
    How much rubber band tension on tattoo machine?
    7 years ago
  • Uta
    Why is there a rubber band around tattoo machines?
    7 years ago
  • Lavinia
    How to put rubberband on tattoo machine?
    7 years ago
  • charles
    How to use feeler gauge for tattoo machine?
    7 years ago
  • zahra
    How tight should the rubberband on a tattoo machine be?
    7 years ago
  • Selina
    How to release tention off the tattoomachine needle?
    7 years ago
  • charlie
    What causes blue spark on spring contact screw tattoo machine?
    7 years ago
  • ambessa
    What is the ball bounce test on an armature bar?
    6 years ago
  • Santina Udinesi
    Does bands go from the armature bar to the front coil?
    6 years ago
  • DELFINO
    How tight should the rubber band be on a tattoo machine?
    6 years ago
  • terry vaughn
    How tight should the rubber bands be on a tattoo machine?
    6 years ago
  • Diana
    How to re assemble coils to a tattoo frame the wires broke a little?
    6 years ago
  • Selam
    How build tattoo coils?
    5 years ago
  • abdul whitaker
    How much tension on the rubberband for liner tattoo gun?
    5 years ago
  • Jakub
    Why do you have to put a rubberband on tattoo machines coils?
    5 years ago
  • Jennifer Terry
    What is the purpose of rubber band on tattoo machine?
    5 years ago
  • kaci
    Why do artists put a rubberband around the coils of a tattoo gun?
    5 years ago
  • semere
    How much tension should an elastic put on a tattoo needle?
    5 years ago
  • razanur
    How tight to put the rubber band on a tattoo liner?
    5 years ago
  • kiara mitchell
    Where to put rubber bands on a rotary machine?
    5 years ago
  • jessica
    Why wont tattoo machine work when rubber band is on?
    4 years ago
  • luana
    Is it ok to file the front coil so armature bar hits flush?
    4 years ago
  • frank baum
    What causes o rings to break on tattoo machines?
    4 years ago
  • Giordana
    How do you use rubberbands on tattoo machine?
    4 years ago
  • Alberto
    DO YOU USE RUBBER BANDS ON ROTARY TATTOO MACHINES?
    4 years ago
  • elen semere
    Why are there rubberbands on tattoo machines?
    4 years ago
  • holfast
    What are the cross drilled armature bars used for tattoo machines?
    4 years ago
  • santina pinto
    How tight should the needle bar be fixed to the armature bar of a tattoo machine?
    4 years ago
  • semolina proudfoot
    Why do you put rubber bands around the coils on a tattoo gun?
    4 years ago
  • elias
    Can the rubber band on tattoo machine be wrinkled?
    4 years ago
  • KRISTIAN
    Why is my tattoo needle spitting ink?
    3 years ago
  • Sean
    How many fuses in tattoo machine?
    3 years ago
  • mckenzie
    Why do tattoo guns use elastic bands?
    3 years ago
  • girma
    When a rubber band cuts on a tattoo machine how do you work it out?
    3 years ago
  • Jerry
    Why do you have to put rubber bands on the coil of the machine?
    3 years ago
  • Douglas Smith
    What type of armature bar to use on liner tattoo machine?
    3 years ago
  • Tuomas Takkula
    Can u use an elestick band to tattoo as a ink?
    3 years ago
  • Sara
    How often should you change o rings on tattoo machine?
    3 years ago
  • HAILE
    How to wire the clip cord wires from a tattoo gun?
    3 years ago
  • melba mugwort
    Do you need elastic bands with a rotary tattoo machine?
    3 years ago
  • FREDRIK
    What kind of rubber bands do you use for tattoo machines?
    3 years ago
  • johnny
    How many rubber bands should you use on liner?
    3 years ago
  • gerontius
    Why out rubber band around coils?
    3 years ago
  • toni
    What kind of rubber band do you use for tattoo gun?
    3 years ago
  • renato
    Do i bend my armarter bar to get deeper strokes on my tattoo machine?
    3 years ago
  • ari-pekka
    Why is the rubber band not geeting tight on my tattoo gun?
    3 years ago
  • Nicoletta
    How snug should the needle be in the ink tube in a rotary machine?
    3 years ago
  • renzo palermo
    Why are there rubber bands on tattoo guns?
    3 years ago
  • KRISTEN
    Why my tattoo machine start and stop?
    3 years ago
  • risto wiljakainen
    How to put ruuber band tattoo?
    3 years ago
  • pimpernel
    How to make my tattoo gun run straiggt?
    3 years ago
  • shane
    Why is my tattoo machine running straight out of ink?
    3 years ago
  • Walter
    How to raise your amature bar on your machine?
    3 years ago
  • topias
    Can i put steel wool in my tattoo machine?
    3 years ago
  • jared
    How do you wrap a rubber band around a tattoo gun?
    3 years ago
  • BENJAMIN
    How to check aset of tattoo coils are any good without disassembling?
    3 years ago
  • heribald gardner
    Where does the elqstic go on a rotary tattoo gun?
    3 years ago
  • eyob
    How to stop sparking tattoo machines?
    3 years ago
  • simret
    What makes your tattoo gun spit out too much ink?
    3 years ago
  • Selassie
    How tight should the elastic band on a tattoo machine?
    3 years ago
  • venanzio
    How to install o rings on tattoo guns and what are they for?
    3 years ago
  • johanna faust
    Why do tattoo artist use rubber bands?
    3 years ago
  • stefan
    How to stop needle from moving alot on tattoo gun?
    3 years ago
  • Mebrahtu Amanuel
    How to stop tattoo gun spitting ink?
    3 years ago
  • Olli
    Where do the black o ring go at on the tattoo gun?
    3 years ago
  • elisa
    How to use a rubberband on a rotary tattoo gun?
    3 years ago
  • sabine
    What we have to do when armature bar of tattoo machine hitting the coil?
    3 years ago
  • Bernd Hirsch
    Where does the grommet go on a rotary tattoo machine with a slider?
    3 years ago
  • SOFIA
    Does slower needle travel need thicker ink?
    3 years ago
  • marcus
    What are rubbands used for on tattoo gun?
    3 years ago
  • robert
    Where does the little black thick rubber band go on my tattoo gun?
    3 years ago
  • leigha
    How do rubber bands go on a dragoart tattoo gun ?
    3 years ago
  • heikki
    Why does the elastic band keep snapping on my tattoo machine?
    3 years ago
  • tesfay
    How to repair loose coils on tattoo machine?
    3 years ago
  • Mattie
    How go fix up a cheap tattoo gun?
    3 years ago
  • david
    What purpose does rubber band serve in tattoo machine?
    3 years ago
  • anton
    How to put tattoo ruber band?
    3 years ago
  • zane
    Why is my tattoo gun gettin loose?
    3 years ago
  • Yolanda
    How many rounds rubber band needs for good tension for tattoo machine?
    3 years ago
  • Bibiana
    Why doesnt my tatto machine always relise ink?
    3 years ago
  • anthony
    How to wrap rubber band on tattoo machine?
    3 years ago
  • Cerdic
    How to use a rubberbannd on a tattoo gun?
    3 years ago
  • Carlos
    Why does my clip cord keep popping out of my binding post?
    3 years ago
  • malva
    Why do tattooist put elstic bands roubd the needke?
    3 years ago
  • adiam
    How tight elastic band on coil tattoo machine?
    3 years ago
  • goldilocks
    How to stop tattoo needle from bouncing?
    3 years ago
  • alexander
    What do you do when your tattoo gun is assembled but wont work?
    3 years ago
  • PAUL
    Do you need to replace the tube in a tattoo gun?
    3 years ago
  • Tesfalem
    How to stop a tattoo needle from rubbing the tube?
    3 years ago
  • josie
    Why does my tattoo coil machine sparks up where the contact screw and spring touch?
    3 years ago
  • keke mikkola
    Where to put rubberbandon tattoo gun?
    3 years ago
  • juliette fraser
    How to set up a tattoo machine in such a way it doesn't spit ink?
    3 years ago
  • Anja
    Why is my tattoo machine making small sparks?
    3 years ago
  • tapani myll
    How to avoid tattoo gun not injecting ink?
    3 years ago
  • birikti
    What to do when my wires from my coils on my tattoo gun brakes?
    3 years ago
  • diann harris
    What if your contact screw wont line up with armature bar?
    3 years ago
  • razanur
    Why did my tattoo gun just stopped working in the middle of a tattoo?
    3 years ago
  • seppo
    Do rotary tattoo machines need a rubberband?
    3 years ago
  • dimitri
    Why doeant my tattoo.machine?
    3 years ago
  • lesley
    Why does my tattoo gun slowly lose power or slow down?
    3 years ago
  • Rina
    How to insert oring in tatto gun?
    3 years ago
  • catherine
    How to attach rubber band to tattoo needle?
    3 years ago
  • mezan sheshy
    Why does my tattoo machine bounce?
    3 years ago
  • stefan ven
    How to use a tattoo machine and maintain?
    3 years ago
  • kidane
    Why the buzz isnt working when i set up a tattoo gun?
    3 years ago
  • gioele
    How to fine tune a dragonhawk tattoo gun?
    3 years ago
  • emma
    When i put on rubber band on my tattoo machine the needle should be dead centre of the tube?
    3 years ago
  • esa
    What to do if your tattoo machine is double hitting?
    3 years ago
  • haben
    How to slow down my tattoo machine?
    3 years ago
  • annabel
    Why do my rubber bands keep snapping when i tattoo?
    3 years ago
  • Goytiom Berhane
    How to insert the black rubber o ring to your tattoo gun?
    3 years ago
  • amaranth
    How to fix tattoo machines when armature bar wont come back up?
    3 years ago
  • BISRAT
    What is the function of rubber bands in a tattoo machine?
    3 years ago
  • sol
    Why do the tattoo artist use rubber band on tattoo machine?
    3 years ago
  • Nina
    What are the vertical tattoo guns called?
    3 years ago
  • aino
    How to clean a armature bar on a tattoo machine?
    2 years ago
  • Kifle
    When i put my foot on my tattoo pedal the amp loses power?
    2 years ago
  • MARIA GRAZIA SICILIANO
    How to assemble the amuture bar on aprofessiona tattoo 0gunl?
    2 years ago
  • beatrice walker
    Why have rubber in the coil tattoo machines?
    2 years ago
  • MARIA
    What type of rubber bands to put on a tattoo machine?
    2 years ago
  • Demsas Alem
    What to run your coil tattoo machine at for consistent black?
    2 years ago
  • Asphodel
    How much space should be between my armature bar and my pin on my lining tattoo machine?
    2 years ago
  • Andi
    Why are there rubber bands in the tattoo kits?
    2 years ago
  • NADINE
    Why do tattoo artists use a rubber band on their guns?
    2 years ago
  • gracie
    How do tattoo machine rubber bands work?
    2 years ago
  • grimalda
    How to put a rubber band on a coil tattoo machine?
    2 years ago
  • Pia
    How to set up a rotary tattoo machine for shading?
    2 years ago
  • mildred
    How many rubber bands do u have to put on a inkstar tattoo gun?
    2 years ago
  • bowman
    What kind of rubber band do i use for my tattoo machine?
    2 years ago
  • ivan
    Do I need gloves to use atattoo gun?
    2 years ago
  • rodney
    Is the armature bar too short for my tattoo machine?
    2 years ago
  • adalberta
    How to stop tattoo machine from spitting ink?
    2 years ago
  • charley brown
    What does it mean when ink spits out the end of your tattoo machine?
    2 years ago
  • jayden watt
    Why would my tattoo machine bogg down when I turn it to one side?
    2 years ago
  • daniel bradley
    How to wrap rubber bands on tattoo gun?
    2 years ago
  • risto
    What is the proper voltage setting for a dragoart tattoo gun?
    2 years ago
  • federica
    Can a liner have low tension for tattooing?
    2 years ago
  • Uta
    Is it possible a screw on my tattoo gun could be too loose or to tight?
    2 years ago
  • donnamira
    How to present a tattoo machine from spitting?
    2 years ago
  • peony gardner
    Where do u attach elastics to stop the needle from bouncing out of the tip of a tattoo machine?
    2 years ago
  • zachary
    What is the perposeof a elastic band on a tatto gun?
    2 years ago
  • selamawit
    What are rubber rings for a tattoo gun for?
    2 years ago
  • aloisia loggia
    How to fix a tube vice that is too small on a tattoo machine?
    2 years ago
  • amalda
    Is it ok to put rubber bands around supplies in a hospital?
    2 years ago
  • stefan
    Which side of tatto motor does foot pedal go in?
    2 years ago
  • doris andersen
    Why do people use rubber bands tattoo funs?
    2 years ago
  • Brad Docherty
    How to make a elastic band on a tattoo machine look slow?
    2 years ago
  • semere
    How to make tatto machine using fixer?
    2 years ago
  • melvin
    Why do tattooist use elacstic bands?
    2 years ago
  • ann cruz
    What are the black rubber rings for with the tattoo gun?
    2 years ago
  • Luam
    How to fix shooting problem tattoo machine?
    2 years ago
  • kenneth ingraham
    Where does rubber band go to make the pin bounce on a tattoo machine?
    2 years ago
  • alisha
    Where does rubber bands go on tatoo machine?
    2 years ago
  • ted
    Where do small black rubber bands go on a tattoo gun?
    2 years ago
  • aziz
    How to make the screw on the tattoo machine stay in place?
    2 years ago
  • gerda
    How to stop tattoo gun vibrate alot?
    2 years ago
  • Matteo
    How many rubber bands and voltage setting to tattoo knuckles?
    2 years ago
  • Mauri
    Where does the elastic band on the tattoi gun go?
    2 years ago
  • clare
    Why tatoo needle shakes?
    2 years ago
  • impi tuimala
    Why to use rubber band in tattoo machine or alternate exist?
    2 years ago
  • giorgia
    Is it necessary to tide up a rubber band on a tattoo machine?
    2 years ago
  • Weronika
    How many number 12 rubber bands do you use to tattoo?
    2 years ago
  • Robbie
    Why is my liner tattoo gun not moving up and down?
    2 years ago
  • alina
    Why does my needle spit all the ink out when i touch the skin?
    2 years ago
  • JASMINE
    Does my tattoo shading machine need a rubber band on it?
    2 years ago
  • omar
    How to pop ink in the tattoo mechain?
    2 years ago
  • vesa
    What can i put in a tattoo machine if i dont have a oring for the needle head?
    2 years ago
  • Oona
    How to wrap a rubber jand around a tattoo gin?
    2 years ago
  • Makda
    How to maintain the needle on front of my tattoo machine(pictures)?
    2 years ago
  • Afwerki
    How to rubber band fit tatoo machine?
    2 years ago
  • Hannes
    Why do my o rings keep breaking on my tattoo machine?
    2 years ago
  • antje
    What are the rubbers on rotary tattoo guns for?
    2 years ago
  • Jessika
    Why do my tattoo liners have no power?
    2 years ago
  • james wolff
    How does rubb sa maciens tattooz?
    2 years ago
  • ronald
    How often do you change the rubber o ring on tattoo gun?
    2 years ago
  • patrick
    What is the o ring for on tattoo machine spring?
    2 years ago
  • T Zaragamba
    How many rubber bands to put around a liner needle?
    2 years ago
  • louie
    What are orings for on a tattoo machine?
    2 years ago
  • tahvo
    Do tattoo machines make a small spark?
    2 years ago
  • Hilda
    What rubberbands should i use for my tattoo liner gun?
    2 years ago
  • daisy
    How to make tattoo gun needle stay on grommet?
    2 years ago
  • Peregrin
    Why does my tattoo gun rattle?
    2 years ago
  • zachary
    Where does the rubber band go a tattoo machjne?
    2 years ago
  • mehari
    What are the small thick round little rubber bands for tattoo guns where they go?
    2 years ago
  • Elizabeth Collins
    What size of rubber band do i need for tattooing?
    2 years ago
  • karolin
    How to use raber band tatto gun?
    2 years ago
  • Jakob Davidson
    Where to put rubber bamds on tattoo gun?
    2 years ago
  • Phillipp
    Do tattoo machines require a rubber band?
    2 years ago
  • Teodata Buccho
    What could make my tattoo gun stall?
    2 years ago
  • STEFAN
    What size rubber band for tattoo machine?
    2 years ago
  • shishay
    How tight should you have the rubber bands on the back of your gauges?
    2 years ago
  • Stefan
    How to connect a tattoo machine with a rubber?
    2 years ago
  • CLOTILDE
    What size rubber bands for tattoo machine?
    2 years ago
  • Brogan
    What size rubber for tattoo machines?
    2 years ago
  • Birgit
    Why do I have to flick my armature bar to run my tattoo machine?
    2 years ago
  • MARTHA
    What type of bands to use on coils?
    2 years ago
  • joseph
    How make tatto machine with switch and needle changing system?
    2 years ago
  • Semhar
    How to solve my tattoo middle problem?
    2 years ago
  • eric
    How cable coil tattoo?
    2 years ago
  • ali simon
    How to make tatoo machine neddle base?
    2 years ago
  • William
    Can i make a tattoo spring by steel for rotary tattoo machine?
    2 years ago
  • Maria
    How to make a rubber tatto machine?
    2 years ago
  • Maurilio
    How to use rubbers in a tattoo mechane?
    1 year ago
  • Juliane Strauss
    How to stop tattoo gun vibration?
    1 year ago
  • ROBIN
    Why does my ink spit when i step on my tattoo gun pedal?
    1 year ago
  • haile
    How to cot a rubber on a tattoo machine menu?
    1 year ago
  • Zufan Medhanie
    How to control flow of ink in tatoo machine?
    1 year ago
  • saba
    How to connect à tatto machine to make vibrations?
    12 months ago
  • virpi
    How toght should a rubber band be on a tattoo machine?
    12 months ago
  • dodinas
    What could be wrong when a tattoo machine shuts itself whist tattooing?
    12 months ago
  • marigold
    What is reason to tie rubber band on tattoo mashine?
    10 months ago
  • MARIA
    Where do the elastics go on a rotary tattoo machine?
    10 months ago
  • WILLIE
    What to check on tattoo gun when pedal works but no power to the gun?
    9 months ago
  • guy mackenzie
    Why is my tattoo machine not keeping tabs?
    9 months ago
  • Ralph
    Where do the rubber grommets go on a tattoo machine?
    9 months ago
  • luca
    How to secure tattoo needle?
    5 months ago
  • Kristiina
    How do i assemble a tattoo gun rubber band?
    3 months ago
  • ronald
    How do you set up a tattoo gun rubber bans?
    1 month ago
  • Amaranth
    When shading a tattoo do you still need to use a elastic band?
    1 month ago

Post a comment